OEM Air Filter - am I wishing too hard?

This is for general posts and questions concerning only the Voyager XII (1200cc, Four-cylinder) Years 1986 thru 2003.

Moderators: the2knights, Highway Rider

Post Reply
User avatar
drtechnology
Traveler
Traveler
Posts: 100
Joined: Fri Jun 12, 2020 11:35 pm
4
Current bike(s): 2002 Voyager XII
Has liked: 113 times
Been liked: 17 times

OEM Air Filter - am I wishing too hard?

Post by drtechnology »

I did a search first only found the "buy a car one and chop it's sides off and rubber glue it in.

Blah! I do see Gertrude gets an air filter post talks about an OEM one, but no link... Any idea if an OEM or even better a k&n type is available? I have not taken a look at my filter but the bike is a 2002 model with 45k miles and when I bought it orig owner said never replaced air filter so it might be time to help it breathe better - especially in Vegas with 110 to 120 summer temps coming up - more airflow cannot hurt

Any ideas where I can get it - and is it easy to change out? Anyone attempted this before - did search again on replacing it do not see many people talking about how and where (I can figure it out - follow the tunnels from holes in front) - but if u have attempted this is it fairly easy

Maybe it will be ok as i'm at only 45k miles and does not need changing?? IDFK, the service manual does not talk much about when to replace air filter - or maybe I was not reading it fully enough? :?:
cushman eagle
King of the Road
King of the Road
Posts: 1982
Joined: Sat Jan 22, 2011 10:08 pm
13
Current bike(s): '99 Kawasaki Voyager 1200
1958 Cushman Eagle restoration has been finished,and have put 3030 miles on her!
Location: Orrville,Ohio
Has liked: 852 times
Been liked: 290 times

Re: OEM Air Filter - am I wishing too hard?

Post by cushman eagle »

Hi,drtechnology,welcome to the AVA family :thmup: You will find friendly help from our family.
The filter is available from bikebandit under part number 11013-1137 for $34.85.
To change it,remove the fake tank by remove the 2 screws near the back on both sides,and loosen the 2 thumb nuts near the center on the bottom.Rest the fake tank on the seat so you do not need to unplug the cruise control wires.
The filter can be removed by unscrewing the 4 screws on the top of the filter box,about a 5 minute job. :wnk2:
These users liked cushman eagle's post:
drtechnology (Tue Jun 16, 2020 8:17 am)
Rating: 11.11%
'99 Voyager VXII,'58 Cushman Eagle
User avatar
GrandpaDenny
King of the Road
King of the Road
Posts: 1078
Joined: Fri Nov 01, 2019 4:24 pm
5
Current bike(s): 1993 Kawasaki Vulcan 1500
Has liked: 481 times
Been liked: 435 times

Re: OEM Air Filter - am I wishing too hard?

Post by GrandpaDenny »

I got mine from Partzilla, part number 11013-1137 for $34.07. It was part of a large order so the shipping was free. Ordered alone, the shipping is $7.95. I believe the K&N filter is around $45.00, but don't quote me on that - NEVER rely upon my memory.
These users liked GrandpaDenny's post:
drtechnology (Tue Jun 16, 2020 8:17 am)
Rating: 11.11%
Dennis Fariello
Philadelphia, PA
2000 Voyager XII "Gertrude" - deceased
1993 Vulcan 88 "Emily"

South Jersey Retreads
Patriot Guard Riders
Warriors Watch Riders

VXII Manuals:
https://amervoyassoc.org/zg1200manuals.php
User avatar
drtechnology
Traveler
Traveler
Posts: 100
Joined: Fri Jun 12, 2020 11:35 pm
4
Current bike(s): 2002 Voyager XII
Has liked: 113 times
Been liked: 17 times

Re: OEM Air Filter - am I wishing too hard?

Post by drtechnology »

so k&n does have a filter for this bike? Cool! I went to their site, typed in my model, make, year only showed an oil filter - guess I shall google and see what comes up lmao. At least I have the part numbers for the air filters stock options, may be easier to just keep replacing stock ones than doing washable k&n lol. How often should we change them for this bike... err after how many miles I guess I will ask do y'all normally change them?
triton28
King of the Road
King of the Road
Posts: 1006
Joined: Fri Aug 23, 2013 1:32 am
11
Current bike(s): 1987 ZG-1200 B1
1987 ZG-1200 B1
1990 ZG-1200 B4
Location: Nova Scotia Canada
Has liked: 105 times
Been liked: 273 times

Re: OEM Air Filter - am I wishing too hard?

Post by triton28 »

The K&N filter # is: 33-2008-1
It is from a 1988 Camaro, 5.0 liter MFI
It will need trimming to fit
These users liked triton28's post:
drtechnology (Tue Jun 16, 2020 8:17 am)
Rating: 11.11%
cushman eagle
King of the Road
King of the Road
Posts: 1982
Joined: Sat Jan 22, 2011 10:08 pm
13
Current bike(s): '99 Kawasaki Voyager 1200
1958 Cushman Eagle restoration has been finished,and have put 3030 miles on her!
Location: Orrville,Ohio
Has liked: 852 times
Been liked: 290 times

Re: OEM Air Filter - am I wishing too hard?

Post by cushman eagle »

drtechnology wrote: Sun Jun 14, 2020 8:08 am so k&n does have a filter for this bike? Cool! I went to their site, typed in my model, make, year only showed an oil filter - guess I shall google and see what comes up lmao. At least I have the part numbers for the air filters stock options, may be easier to just keep replacing stock ones than doing washable k&n lol. How often should we change them for this bike... err after how many miles I guess I will ask do y'all normally change them?
I look at my filter during my annual "winter service" down time.This past winter,the filter was so clean,I just did a quick pass with my shop vac. :thmup:
I did slightly more cleaning last year,but still did not install the filter I keep on stock.I now have about 15,000 miles on the filter in the bike. :thk:
These users liked cushman eagle's post:
drtechnology (Tue Jun 16, 2020 8:17 am)
Rating: 11.11%
'99 Voyager VXII,'58 Cushman Eagle
User avatar
GrandpaDenny
King of the Road
King of the Road
Posts: 1078
Joined: Fri Nov 01, 2019 4:24 pm
5
Current bike(s): 1993 Kawasaki Vulcan 1500
Has liked: 481 times
Been liked: 435 times

Re: OEM Air Filter - am I wishing too hard?

Post by GrandpaDenny »

drtechnology wrote: Sun Jun 14, 2020 8:08 am so k&n does have a filter for this bike? Cool! I went to their site, typed in my model, make, year only showed an oil filter - guess I shall google and see what comes up lmao. At least I have the part numbers for the air filters stock options, may be easier to just keep replacing stock ones than doing washable k&n lol. How often should we change them for this bike... err after how many miles I guess I will ask do y'all normally change them?
You're right, no K&N air filter. Problem with having two different bikes, get confused over who has what for which. Damn the '70s :LAngel
These users liked GrandpaDenny's post:
drtechnology (Tue Jun 16, 2020 8:18 am)
Rating: 11.11%
Dennis Fariello
Philadelphia, PA
2000 Voyager XII "Gertrude" - deceased
1993 Vulcan 88 "Emily"

South Jersey Retreads
Patriot Guard Riders
Warriors Watch Riders

VXII Manuals:
https://amervoyassoc.org/zg1200manuals.php
User avatar
drtechnology
Traveler
Traveler
Posts: 100
Joined: Fri Jun 12, 2020 11:35 pm
4
Current bike(s): 2002 Voyager XII
Has liked: 113 times
Been liked: 17 times

Re: OEM Air Filter - am I wishing too hard?

Post by drtechnology »

Thanks, everyone.... I do not like "trimming" filters because you have a weak spot where trimmed and air may get thru without being filtered more easily = more wear. That's just my opinion tho, I am kinda picky lol.

So no K&N which is ok means no washing no oils, and I see they last a while, prolly why the old owner never replaced - I bet when I open it up will be decent. But their not expensive might just change out with one of those OEM ones for the heck of it. Cannot hurt :) I am looking forward to the Rally Next year - I am 100% going :)
User avatar
Nails
King of the Road
King of the Road
Posts: 1771
Joined: Thu Feb 16, 2017 4:37 pm
7
Current bike(s): '97 XII
'00 XT350
'85 KLR 250
'82 Silverwing Sushiguzzi
Location: New Mexico Rockies
Has liked: 228 times
Been liked: 602 times

Re: OEM Air Filter - am I wishing too hard?

Post by Nails »

I don't really get all the excitement over K&Ns.
https://www.nicoclub.com/archives/kn-vs-oem-filter.html
These users liked Nails's post:
drtechnology (Tue Jun 16, 2020 9:11 pm) • Molalla+Voyager (Fri Jun 26, 2020 1:54 pm)
Rating: 22.22%
--
Nails
Molalla+Voyager
Cruiser
Cruiser
Posts: 31
Joined: Sun Apr 26, 2020 11:19 pm
4
Current bike(s): 2000 Voyager zg1200 XII,
2005 Connie ZG1000
Location: Molalla, OR
Has liked: 35 times
Been liked: 8 times

Re: OEM Air Filter - am I wishing too hard?

Post by Molalla+Voyager »

Nails:
I saw that study a few years ago, it has dissuaded a lot of people I know from using K&N or the likes of many times.
Thank You for bringing it to our attention again.
Steve
These users liked Molalla+Voyager's post:
drtechnology (Mon Jun 29, 2020 7:54 pm)
Rating: 11.11%
Steve
KI7MFT
146.960
User avatar
ekap1200
Master Fabricator
Master Fabricator
Posts: 1364
Joined: Fri Jul 04, 2008 12:54 pm
16
Current bike(s): 2000 voyager end of year total. 108.634
Location: Williamstown, New Jersey
Has liked: 33 times
Been liked: 134 times

Re: OEM Air Filter - am I wishing too hard?

Post by ekap1200 »

Hello from NJ, I also did not like the idea of cutting and gluing at every filter change. So using the STP air filter , as you see in these photos I fabricated a transition plate. and milling a grove around the perimeter , secured into the stock air box with abs glue.

Now its just a few minuets to change out.
Gene Kap.
Attachments
stp_retofit.jpg
stp_retofit.jpg (31.81 KiB) Viewed 1028 times
stpretro 004.JPG
stpretro 004.JPG (37 KiB) Viewed 1028 times
These users liked ekap1200's post:
drtechnology (Mon Jun 29, 2020 12:36 am) • Barry (Sat Jul 11, 2020 9:48 pm)
Rating: 22.22%
"Its not bad if you don't know something, but when you don't know you don't know; That's when your in trouble". Joe Place 1912-2008 (my grandfather)
User avatar
drtechnology
Traveler
Traveler
Posts: 100
Joined: Fri Jun 12, 2020 11:35 pm
4
Current bike(s): 2002 Voyager XII
Has liked: 113 times
Been liked: 17 times

Re: OEM Air Filter - am I wishing too hard?

Post by drtechnology »

ekap1200 wrote: Sun Jun 28, 2020 10:06 pm Hello from NJ, I also did not like the idea of cutting and gluing at every filter change. So using the STP air filter , as you see in these photos I fabricated a transition plate. and milling a grove around the perimeter , secured into the stock air box with abs glue.

Now its just a few minuets to change out.
Gene Kap.
While that looks cool, is the stp (or any "alternative to OEM" filter) that much of an increase in mpg or that better that as long as stock is available, I would not just go with stock? Just curious, and if it is way better to use the newer filters instead of an old ass (but new) stock one, I may just do as you did. My idea is as long as stock is still readily available why not just stick with it?
User avatar
ekap1200
Master Fabricator
Master Fabricator
Posts: 1364
Joined: Fri Jul 04, 2008 12:54 pm
16
Current bike(s): 2000 voyager end of year total. 108.634
Location: Williamstown, New Jersey
Has liked: 33 times
Been liked: 134 times

Re: OEM Air Filter - am I wishing too hard?

Post by ekap1200 »

You will not even notice it.... its such a large filter to begin with on such a small engine.. I got an average of 50mpg before and avg. of 50mpg using the STP. My opinion is that, cutting and gluing adds the risk of debris fouling the carbs . I now have 107,247 miles on this bike , having never removed the carbs. Starts and runs the same as it did when brand new. I use Seafoam from time to time and several times in the season , I drain the carb bowls. I also change the fuel/flt every 25,000 mi.
There are original filters to be found, but keep in mind just how old they are....
Gene K.
"Its not bad if you don't know something, but when you don't know you don't know; That's when your in trouble". Joe Place 1912-2008 (my grandfather)
User avatar
drtechnology
Traveler
Traveler
Posts: 100
Joined: Fri Jun 12, 2020 11:35 pm
4
Current bike(s): 2002 Voyager XII
Has liked: 113 times
Been liked: 17 times

Re: OEM Air Filter - am I wishing too hard?

Post by drtechnology »

ekap1200 wrote: Mon Jun 29, 2020 12:00 pm You will not even notice it.... its such a large filter to begin with on such a small engine.. I got an average of 50mpg before and avg. of 50mpg using the STP. My opinion is that, cutting and gluing adds the risk of debris fouling the carbs . I now have 107,247 miles on this bike , having never removed the carbs. Starts and runs the same as it did when brand new. I use Seafoam from time to time and several times in the season , I drain the carb bowls. I also change the fuel/flt every 25,000 mi.
There are original filters to be found, but keep in mind just how old they are....
Gene K.
I agree, maybe old, but as long as physically they are in good shape, they should provide that "stock perfect seal" and hopefully nothing gets into carbs? IDK?? I guess I am just taking the easy road for now. I actually have not even opened air filter to see what previous owner did - maybe he had it modified already. Just thinking out loud lol.
User avatar
drtechnology
Traveler
Traveler
Posts: 100
Joined: Fri Jun 12, 2020 11:35 pm
4
Current bike(s): 2002 Voyager XII
Has liked: 113 times
Been liked: 17 times

Re: OEM Air Filter - am I wishing too hard?

Post by drtechnology »

TBH anyone have some money to invest I bet we can get rich, looking at this thread alone, off makin g "stock" Kawa parts but that are actually aftermarket parts made new by a factory but are done to the exact specs as stock. I.E. making a new air filter that is a stock air filter but made in 2020 not 2002 lol.

Just an idea haha
User avatar
Barry
Grand Tourer
Grand Tourer
Posts: 398
Joined: Thu Feb 21, 2008 2:00 pm
16
Current bike(s): 87 Voyager 12
Has liked: 100 times
Been liked: 69 times

Re: OEM Air Filter - am I wishing too hard?

Post by Barry »

Amsoil used to make air filters to fit the vxii. They look just like the K&N filter. Been running the same filter for 20 years now. Just clean & re oil it every few years. You can buy it off me along with all the boxes of parts & tools. Also comes with an '87 vxii.
Barry
87 Voyager XII
User avatar
drtechnology
Traveler
Traveler
Posts: 100
Joined: Fri Jun 12, 2020 11:35 pm
4
Current bike(s): 2002 Voyager XII
Has liked: 113 times
Been liked: 17 times

Re: OEM Air Filter - am I wishing too hard?

Post by drtechnology »

Barry wrote: Sat Jul 11, 2020 9:53 pm Amsoil used to make air filters to fit the vxii. They look just like the K&N filter. Been running the same filter for 20 years now. Just clean & re oil it every few years. You can buy it off me along with all the boxes of parts & tools. Also comes with an '87 vxii.
Free '87 Voyager with every filter purchase lmao :woohoo:

Yea, sorry I have an '02 XII and am good for now - but thx for the offer <3
User avatar
Scott-(Altoona, PA)
King of the Road
King of the Road
Posts: 1085
Joined: Mon Feb 18, 2008 1:22 pm
16
Current bike(s): 2001 Voyager XII
Location: Altoona, PA
Has liked: 83 times
Been liked: 140 times
Contact:

Re: OEM Air Filter - am I wishing too hard?

Post by Scott-(Altoona, PA) »

Just in case someone finds themselves searching for a cross match for the Air Filter here is a link to a webpage that gives quite a few brands cross matched to the NAPA filter 6140.
Air Filter CrossReference <-- clickable link
These users liked Scott-(Altoona, PA)'s post:
drtechnology (Thu Jul 16, 2020 4:06 am)
Rating: 11.11%
Mid-Atlantic Voyagers chapter secretary {"scribe"}
2001 Voyager XII
We may not know them all, but we owe them all! Thank a Veteran today!
Post Reply

Return to “General - Voyager XII (1200 Four)”