front mirror trim
Moderators: the2knights, Highway Rider
- ekap1200
- Master Fabricator
- Posts: 1364
- Joined: Fri Jul 04, 2008 12:54 pm
- 16
- Current bike(s): 2000 voyager end of year total. 108.634
- Location: Williamstown, New Jersey
- Has liked: 33 times
- Been liked: 134 times
front mirror trim
Hello to all from finally sunny New Jersey. I think were done with winter, As promised this is the mirror trim prototype pictures ,for those who showed some interest in someone bringing these back. I added two arcs to its profile one on the top and one on the outside view; as requested its the same width, on the top 2.0" at its widest point. This is of course not the same material I will be using. It will be the 18 gauge mirrored stainless steel with stainless screws. If anyone has any changes they would like to see done to this design , now is the time. I just received the mirrored Stainless to manufacture these and more vents today
"Its not bad if you don't know something, but when you don't know you don't know; That's when your in trouble". Joe Place 1912-2008 (my grandfather)
-
- Board Member
- Posts: 74
- Joined: Thu Sep 16, 2010 12:12 am
- 14
- Current bike(s): 2003 Voyager xii
2000 Voyager xii
2000 Voyager xii
1988 Voyager xii
1977 Suzuki GT500B
2000 Escapade Cargo Trailer
2001 Escapade Cargo Trailer
2009 Kompact Kamp Cargo Trailer - Location: Lewisberry PA
- Has liked: 0
- Been liked: 5 times
-
- Cruiser
- Posts: 38
- Joined: Sat Aug 10, 2013 9:45 am
- 11
- Current bike(s): 2002 voyager xii
- Location: Ottawa, Ontario Canada
- Has liked: 0
- Been liked: 0
Re: front mirror trim
I agree they will look great! Im interested too! I sent you an email about the vent trim and my interest in ordering,dont know if ya got it but put me in the list please thanks!,Rob!
- Bill O
- Past Board Member
- Posts: 285
- Joined: Mon Feb 18, 2008 12:28 am
- 16
- Current bike(s): 1994 1200 Voyager
2003 1200 Voyager
2003 1200 Voyager TriKing Trike - Location: Las Vegas, NV, USA
- Has liked: 0
- Been liked: 6 times
Re: front mirror trim
Gene, put me down for a set. (Mirror Shields)
Bill O
Bill O
If it ain't broke, don't fix it!
1994 Voyager
2003 Voyager
2003 Voyager TriKing Trike
Nevada Patriot Guard Rider
1994 Voyager
2003 Voyager
2003 Voyager TriKing Trike
Nevada Patriot Guard Rider
- ekap1200
- Master Fabricator
- Posts: 1364
- Joined: Fri Jul 04, 2008 12:54 pm
- 16
- Current bike(s): 2000 voyager end of year total. 108.634
- Location: Williamstown, New Jersey
- Has liked: 33 times
- Been liked: 134 times
Re: front mirror trim
Hello Bill, Were the OEM trim shipped flat, and did it include double sided tape. I put some on this proto and didn't really like the gap at the top. The alternative I have is to add a third screw on the inboard side towards the top . Gene Kap.Bill O wrote:Gene, put me down for a set. (Mirror Shields)
Bill O
"Its not bad if you don't know something, but when you don't know you don't know; That's when your in trouble". Joe Place 1912-2008 (my grandfather)
- Bill O
- Past Board Member
- Posts: 285
- Joined: Mon Feb 18, 2008 12:28 am
- 16
- Current bike(s): 1994 1200 Voyager
2003 1200 Voyager
2003 1200 Voyager TriKing Trike - Location: Las Vegas, NV, USA
- Has liked: 0
- Been liked: 6 times
Re: front mirror trim
Gene,ekap1200 wrote:Hello Bill, Were the OEM trim shipped flat, and did it include double sided tape. I put some on this proto and didn't really like the gap at the top. The alternative I have is to add a third screw on the inboard side towards the top . Gene Kap.Bill O wrote:Gene, put me down for a set. (Mirror Shields)
Bill O
What do you mean by "Flat"? The OEM's came with double sided tape and two screws each, pre-shaped to fit around the mirrors. I didn't use the double sided tape as the permanent adheasive, because the there was an air gap and it would cause a whistle at times going down the road. I used the Tape to position then secured with the screws, then my secret trick.......
Go to a parts store, get a small tube (smaller than tooth paste) of "Black RTV" Cut a very small opening at the end of the pointed cap and put a nice small bead around the front side (back of the mirrors) of the Shields. Fill in any gaps between the shields and the mirrors. If needed, wet your finger to smooth out the bead between the back edge of the shield and the body of the mirror.
Wha-la, no more whistle and the the shiney black bead is pretty much invisable to the eye. Makes for a seamless, custom fit. To this day, the shields on my '94 look as good as they did over 12 years ago.
Bill O
If it ain't broke, don't fix it!
1994 Voyager
2003 Voyager
2003 Voyager TriKing Trike
Nevada Patriot Guard Rider
1994 Voyager
2003 Voyager
2003 Voyager TriKing Trike
Nevada Patriot Guard Rider
- Mr Jensee
- King of the Road
- Posts: 1987
- Joined: Fri Dec 26, 2008 5:55 pm
- 15
- Current bike(s): Phone 337-781-8158
Home Phone disconnected.
Previous bikes. Yamaha 180, Honda CM200T, Suzuki 1000LNKawasaki ZRX1100. - Location: Lafayette, La
- Has liked: 0
- Been liked: 9 times
Re: front mirror trim
Any chance you could come up with a Visor that would fit a Garmin Nuvi? That is what I really need when I use mine. Something that would snap on and off that would keep the sun off the screen. If you decide to make one, patent it and sell millions to those of us bikers who are too cheap to buy motorcycle specific GPS units.
For Voyager XII Manuals click the link below.
https://1drv.ms/f/s!Ao3K0Ai2gvglgS3l7J4pBJrjfBhc
https://1drv.ms/f/s!Ao3K0Ai2gvglgS3l7J4pBJrjfBhc
- ekap1200
- Master Fabricator
- Posts: 1364
- Joined: Fri Jul 04, 2008 12:54 pm
- 16
- Current bike(s): 2000 voyager end of year total. 108.634
- Location: Williamstown, New Jersey
- Has liked: 33 times
- Been liked: 134 times
Re: front mirror trim
Thanks Bill O, The gap at the top had me concerned also. On the proto-type I made I used the tape and just didn't like the air gap . That is why tonight I am making another proto-type with three fasteners and forming it so that it will sit tightly on top. The third screw will be on the inboard side 2-3/4 up from the bottom screw. RTV black would have been my choice also .
Mr Jensee, might be something I may try at some point in time, I don't know of anyone here in N.J. that has a garmin-nuvi , but if I stop in to a Best Buy or Sams Club I will look at one.
I am a bit behind in the shop this week, A rodent had made a nice home under the fuse box housing, of my Chevy pic-up and done some chewing on many wires under there, Causing many issue's and a dead OBD plug, triping the check engine lamp and other engine issues. So far 11 hours of my labor to track down it down to under the fuse block, All these issues happened while I was driving in the last snow we had with gobs of salt on the road. So for a while I was looking at all the wrong places and could not even code the computer as the data plug was dead. To make it all worse, the salt spray under the hood now got into the wire's where the insulation had been chewed off resulting in me having to cut sections out that are being eaten away by the salt. Gee I love a challenge........
Gene Kap
Mr Jensee, might be something I may try at some point in time, I don't know of anyone here in N.J. that has a garmin-nuvi , but if I stop in to a Best Buy or Sams Club I will look at one.
I am a bit behind in the shop this week, A rodent had made a nice home under the fuse box housing, of my Chevy pic-up and done some chewing on many wires under there, Causing many issue's and a dead OBD plug, triping the check engine lamp and other engine issues. So far 11 hours of my labor to track down it down to under the fuse block, All these issues happened while I was driving in the last snow we had with gobs of salt on the road. So for a while I was looking at all the wrong places and could not even code the computer as the data plug was dead. To make it all worse, the salt spray under the hood now got into the wire's where the insulation had been chewed off resulting in me having to cut sections out that are being eaten away by the salt. Gee I love a challenge........
Gene Kap
"Its not bad if you don't know something, but when you don't know you don't know; That's when your in trouble". Joe Place 1912-2008 (my grandfather)
- Furchin
- Cruiser
- Posts: 78
- Joined: Sun Feb 17, 2008 11:48 pm
- 16
- Location: Huntingdon County, PA
- Has liked: 0
- Been liked: 0
Re: front mirror trim
Mr. Jensee,
Do you mean something like these????
http://www.ebay.com/itm/360448565259?ss ... 1423.l2649
Do you mean something like these????
http://www.ebay.com/itm/360448565259?ss ... 1423.l2649
'87 Kawasaki Zl600 Eliminator-Red
'87 Kawasaki ZL1000 Eliminator-Black
'87 Kawasaki ZL1000 Eliminator-Pearl White
'87 Kawasaki ZL1000 Eliminator-Red
'96 Kawasaki Voyager
'87 Kawasaki ZL1000 Eliminator-Black
'87 Kawasaki ZL1000 Eliminator-Pearl White
'87 Kawasaki ZL1000 Eliminator-Red
'96 Kawasaki Voyager
- Mr Jensee
- King of the Road
- Posts: 1987
- Joined: Fri Dec 26, 2008 5:55 pm
- 15
- Current bike(s): Phone 337-781-8158
Home Phone disconnected.
Previous bikes. Yamaha 180, Honda CM200T, Suzuki 1000LNKawasaki ZRX1100. - Location: Lafayette, La
- Has liked: 0
- Been liked: 9 times
Re: front mirror trim
Absolutely! I didn't know anyone made these. Thanks!
For Voyager XII Manuals click the link below.
https://1drv.ms/f/s!Ao3K0Ai2gvglgS3l7J4pBJrjfBhc
https://1drv.ms/f/s!Ao3K0Ai2gvglgS3l7J4pBJrjfBhc
- Bill O
- Past Board Member
- Posts: 285
- Joined: Mon Feb 18, 2008 12:28 am
- 16
- Current bike(s): 1994 1200 Voyager
2003 1200 Voyager
2003 1200 Voyager TriKing Trike - Location: Las Vegas, NV, USA
- Has liked: 0
- Been liked: 6 times
Re: front mirror trim
Mr Jensee wrote:Any chance you could come up with a Visor that would fit a Garmin Nuvi? That is what I really need when I use mine. Something that would snap on and off that would keep the sun off the screen. If you decide to make one, patent it and sell millions to those of us bikers who are too cheap to buy motorcycle specific GPS units.
Have a look at these. They are called Glare Stompers. I bought two different sizes of these for my GPS and and a HP Pocket PC.
http://www.glarestomper.com/
Bill O
If it ain't broke, don't fix it!
1994 Voyager
2003 Voyager
2003 Voyager TriKing Trike
Nevada Patriot Guard Rider
1994 Voyager
2003 Voyager
2003 Voyager TriKing Trike
Nevada Patriot Guard Rider
- ekap1200
- Master Fabricator
- Posts: 1364
- Joined: Fri Jul 04, 2008 12:54 pm
- 16
- Current bike(s): 2000 voyager end of year total. 108.634
- Location: Williamstown, New Jersey
- Has liked: 33 times
- Been liked: 134 times
Re: front mirror trim
Update on new mirror trim. Still working out a repeatable forming process, and will be finished and have a price on them soon. Here are a few pics of the progress at this point. Taking note of a few changes and issues the oem's had , and doing away with the need for adhisive tape by the addition of the 3 rd screw shown in pic. Bill gave me the idea of the bead of atv black on the underside to stop the air from whistling through and the 3rd fastner makes that possible . Thanks to all that have shown interest and I can always be PM'ed for more info or request for other items I may be able to help with to keep our voyagers looking like they are still going strong in the world of shinny new bikes And thank's to all that have requested other trim parts they would like to see someone making again.
Sorry to have raised the price on the vents they are now 56.50 for the set of four /with screws. plus shipping Gene Kap. aka ekap1200
Sorry to have raised the price on the vents they are now 56.50 for the set of four /with screws. plus shipping Gene Kap. aka ekap1200
"Its not bad if you don't know something, but when you don't know you don't know; That's when your in trouble". Joe Place 1912-2008 (my grandfather)
- Lucasind
- King of the Road
- Posts: 1790
- Joined: Mon Dec 17, 2012 5:44 pm
- 11
- Current bike(s): 2003 Voyager 1200
1988 Voyager 1200
1985 Voyager 1300
2008 Concourse 1400
1985 LTD 1100
1981 CSR 1000
1981 CSR 650
1979 KZ 650
1973 XL 350
1988 Eliminator
1975 CB 125
1965 S 65
and a bunch of parts ! - Location: Toledo, OH
- Has liked: 194 times
- Been liked: 69 times
Re: front mirror trim
... I like the placement of the third screw ,on the inboard side. less noticeable.
90% OF ANY JOB ...IS GETTING STARTED !
- Mr Jensee
- King of the Road
- Posts: 1987
- Joined: Fri Dec 26, 2008 5:55 pm
- 15
- Current bike(s): Phone 337-781-8158
Home Phone disconnected.
Previous bikes. Yamaha 180, Honda CM200T, Suzuki 1000LNKawasaki ZRX1100. - Location: Lafayette, La
- Has liked: 0
- Been liked: 9 times
Re: front mirror trim
Gene, since you are working with nice shiny stainless steel, any chance you could come up with that extension that they used to make for the bottom back of the front fender? I know I would want one and I'll bet a number of others would too.
For Voyager XII Manuals click the link below.
https://1drv.ms/f/s!Ao3K0Ai2gvglgS3l7J4pBJrjfBhc
https://1drv.ms/f/s!Ao3K0Ai2gvglgS3l7J4pBJrjfBhc
- ekap1200
- Master Fabricator
- Posts: 1364
- Joined: Fri Jul 04, 2008 12:54 pm
- 16
- Current bike(s): 2000 voyager end of year total. 108.634
- Location: Williamstown, New Jersey
- Has liked: 33 times
- Been liked: 134 times
Re: front mirror trim
Thanks Tony, That was the one of the test bend pcs, moved them both and then I moved the top one again .312 down away from the radius.Lucasind wrote:... I like the placement of the third screw ,on the inboard side. less noticeable.
Dane ' thats a good idea on the skirt, find me some pics and I do something with it. Maybe with the letters AVA water-jeted thru on each side.
Thanks guys Gene Kap.
"Its not bad if you don't know something, but when you don't know you don't know; That's when your in trouble". Joe Place 1912-2008 (my grandfather)
- ekap1200
- Master Fabricator
- Posts: 1364
- Joined: Fri Jul 04, 2008 12:54 pm
- 16
- Current bike(s): 2000 voyager end of year total. 108.634
- Location: Williamstown, New Jersey
- Has liked: 33 times
- Been liked: 134 times
Re: front mirror trim
Hi Mike, Working on that, and also wanting to add text or a logo or just the letters AVA, Just sent Don M. a email to see if the AVA would have any issues with me putting the letters in the front fender skirt. I finally have the mirror trim in process and after I ship what I have ;I have the crash bar to fabricate and put a price on. Thanks for all the great ideas. Gene Kap.Mr Jensee wrote:Gene, since you are working with nice shiny stainless steel, any chance you could come up with that extension that they used to make for the bottom back of the front fender? I know I would want one and I'll bet a number of others would too.
PS_ check out under General Chat/love this embeded stuff debon to see the first set of mirror trim . It went thru some changes , I'll also have them at the rally.
"Its not bad if you don't know something, but when you don't know you don't know; That's when your in trouble". Joe Place 1912-2008 (my grandfather)