Oil sight glass

Got a tech tip for Voyager 12's from your personal experiences, or one complete with pictures and instructions, here's where to post it. You can also ask about tips or procedures here.

Moderators: the2knights, Highway Rider

Post Reply
User avatar
dsmmrm
Cruiser
Cruiser
Posts: 92
Joined: Tue Jun 20, 2017 12:41 pm
7
Current bike(s): 2001 Kawasaki Voyager XII
1996 Kawasaki Vulcan 1500 Classic
Has liked: 0
Been liked: 3 times

Oil sight glass

Post by dsmmrm »

I have read in numerous places here that the sight glass cannot be trusted and will outright lie to you like a delinquent step child. The conventional wisdom appear to be change the oil and filter, be sure to get both drain plugs, and put in 3 quarts plus 22 oz and disregard the sight glass. Correct so far?

So after you have changed it how do you monitor it over the ensuing weeks? Presumably you could see leakage but you still have be able to tell if you are using any, aka burning it. In my case I just got it, the oil looks fairly new but other than draining it out and dumping it back in how can I tell if the PO put in the right amount? :bat:
--
Dave Morrow
Vermilion, Ohio
small herd of kaws
voyager55
Elite Tourer
Elite Tourer
Posts: 820
Joined: Mon Aug 19, 2013 6:08 am
11
Current bike(s): 2003 1200
Location: Eden Prairie, MN
Has liked: 1 time
Been liked: 3 times

Re: Oil sight glass

Post by voyager55 »

I ignore checking oil level. I change oil every 3000 (Rotella Dino oil) and have never had a problem. As stated that oil sight glass can't be trusted and will drive you crazy if you keep checking it.
In your case I'd change it to be sure it was done correctly, Then you don't have to worry
User avatar
dsmmrm
Cruiser
Cruiser
Posts: 92
Joined: Tue Jun 20, 2017 12:41 pm
7
Current bike(s): 2001 Kawasaki Voyager XII
1996 Kawasaki Vulcan 1500 Classic
Has liked: 0
Been liked: 3 times

Re: Oil sight glass

Post by dsmmrm »

Unless, of course, it's using it as a rate that could cause a dangerously low level over those 3k miles. You are right, though. I need to change it regardless since even if it was done recently I don't know what or how much was put in there.
--
Dave Morrow
Vermilion, Ohio
small herd of kaws
User avatar
cranky
King of the Road
King of the Road
Posts: 1037
Joined: Wed Jul 06, 2016 12:36 am
8
Current bike(s): 2003 Voyager
Location: San Jose, KalEfornYa
Has liked: 303 times
Been liked: 80 times

Re: Oil sight glass

Post by cranky »

use the sightglass but put it on the kick stand, at some point you're going to see oil in the in the sightglass and then you can monitor from there. My next change, that is what I'm gonna do....
'03 Voyager - http://tinyurl.com/mqtgpwp VROC pics of Gina
Cranky - Bill Snodgrass AVA # 6544. VROC # 16804
Cranked >128K miles, Mtn bike-no motor!!!
San Jose, KalEfornYa
User avatar
Gator Mike
Traveler
Traveler
Posts: 219
Joined: Mon Feb 18, 2008 12:39 am
16
Current bike(s): 1994 Kawasaki voyager
2002 Honda 750 ACE
1969 Honda 90
Location: Elton, Louisiana
Has liked: 0
Been liked: 0

Re: Oil sight glass

Post by Gator Mike »

crankyb is correct. If I put mine on the kick stand and check it atleast an hour after shut down, the oil level will be about 1/4 of an inch above the bottom of the site glass. I don't worry about the lines on the glass, if there is oil visible its good to go. Guess it could happen but I've never heard of a Voyager using oil. Must be magic. ;-)
"Laisez les bon temps rouler!"

1994 Voyager XII
2001 Honda Ace
1969 Honda CM91

Louisiana Patriot Guard Rider
Combat veterans motorcycle Association
cushman eagle
King of the Road
King of the Road
Posts: 1983
Joined: Sat Jan 22, 2011 10:08 pm
13
Current bike(s): '99 Kawasaki Voyager 1200
1958 Cushman Eagle restoration has been finished,and have put 3030 miles on her!
Location: Orrville,Ohio
Has liked: 854 times
Been liked: 290 times

Re: Oil sight glass

Post by cushman eagle »

The bike does meed to be setting level,as crankyb said,if it is leaning to the right ,or left of vertical it will be off.I check mine at 2000 miles,and change it at 4000-4500.We find on heavy trucks,if they are not setting level,the dipstick can show +or - as much as a gallon off.
'99 Voyager VXII,'58 Cushman Eagle
voyager55
Elite Tourer
Elite Tourer
Posts: 820
Joined: Mon Aug 19, 2013 6:08 am
11
Current bike(s): 2003 1200
Location: Eden Prairie, MN
Has liked: 1 time
Been liked: 3 times

Re: Oil sight glass

Post by voyager55 »

If you want the bike level it needs to be on the center stand
User avatar
dsmmrm
Cruiser
Cruiser
Posts: 92
Joined: Tue Jun 20, 2017 12:41 pm
7
Current bike(s): 2001 Kawasaki Voyager XII
1996 Kawasaki Vulcan 1500 Classic
Has liked: 0
Been liked: 3 times

Re: Oil sight glass

Post by dsmmrm »

Thanks for the clarification, v55 and cushman. That's what I thought cranky and mike meant but it's nice to have corroboration.
--
Dave Morrow
Vermilion, Ohio
small herd of kaws
User avatar
cranky
King of the Road
King of the Road
Posts: 1037
Joined: Wed Jul 06, 2016 12:36 am
8
Current bike(s): 2003 Voyager
Location: San Jose, KalEfornYa
Has liked: 303 times
Been liked: 80 times

Re: Oil sight glass

Post by cranky »

.... for me, put the scoot level front to back, put it on the side stand
so can see a noticeable oil level....
'03 Voyager - http://tinyurl.com/mqtgpwp VROC pics of Gina
Cranky - Bill Snodgrass AVA # 6544. VROC # 16804
Cranked >128K miles, Mtn bike-no motor!!!
San Jose, KalEfornYa
Thadbaker86voyager
Cruiser
Cruiser
Posts: 79
Joined: Thu Jan 28, 2016 12:43 am
8
Current bike(s): 1990 XII Voyager
1986 XII Voyager
Has liked: 0
Been liked: 2 times

Re: Oil sight glass

Post by Thadbaker86voyager »

I changed oil, put in proper amount (3 quarts 22oz). Parked it on the same level spot, on center stand, and noted where level was in sight glass. For mine around the center of the glass, maybe slightly below. Always park it in the same place, on center stand, and check it before next ride. Has stayed the same level. Previous owner had it way over full and it would smoke on start up, plus tapet noise. Correct level, cured smoke and noise! :thmup: has been perfect for several months now.
User avatar
dsmmrm
Cruiser
Cruiser
Posts: 92
Joined: Tue Jun 20, 2017 12:41 pm
7
Current bike(s): 2001 Kawasaki Voyager XII
1996 Kawasaki Vulcan 1500 Classic
Has liked: 0
Been liked: 3 times

Re: Oil sight glass

Post by dsmmrm »

I read a post somewhere here that said the biggest symptom of overfilled oil was lifter noise due to the oil foaming. I'm not experiencing that or smoking so I guess It's at least not overfilled. In fact, the motor is very quiet in general. I had read so much about transmission noise and such I was prepared to be sitting on a clothes washer. I was pleasantly surprised that this is not the case.
--
Dave Morrow
Vermilion, Ohio
small herd of kaws
voyager55
Elite Tourer
Elite Tourer
Posts: 820
Joined: Mon Aug 19, 2013 6:08 am
11
Current bike(s): 2003 1200
Location: Eden Prairie, MN
Has liked: 1 time
Been liked: 3 times

Re: Oil sight glass

Post by voyager55 »

It foams and creates noisy lifters to
cushman eagle
King of the Road
King of the Road
Posts: 1983
Joined: Sat Jan 22, 2011 10:08 pm
13
Current bike(s): '99 Kawasaki Voyager 1200
1958 Cushman Eagle restoration has been finished,and have put 3030 miles on her!
Location: Orrville,Ohio
Has liked: 854 times
Been liked: 290 times

Re: Oil sight glass

Post by cushman eagle »

cushman eagle wrote:The bike does meed to be setting level,as crankyb said,if it is leaning to the right ,or left of vertical it will be off.I check mine at 2000 miles,and change it at 4000-4500.We find on heavy trucks,if they are not setting level,the dipstick can show +or - as much as a gallon off.
I failed to mention,that my bike needs to be on the center stand to be level,not the side stand. :bat:
'99 Voyager VXII,'58 Cushman Eagle
User avatar
ghostler
Grand Tourer
Grand Tourer
Posts: 519
Joined: Fri Jun 21, 2013 5:44 pm
11
Current bike(s): 2001 Voyager XII, 1971 Honda CB100
Asphalt, the final frontier; these are the treks of the Kawasaki Voyager; its continuing mission to explore strange new roads, to seek out new sites, new bed & breakfasts, to boldly ride where no one has ridden before.
Location: Clovis, NM
Has liked: 2 times
Been liked: 10 times
Contact:

Re: Oil sight glass

Post by ghostler »

Bike is not much different than a modern car engine. Unless one is losing oil through poor sealing gaskets, poor sealing piston rings or valve guide seals, etc., oil loss is very minimal between normal change intervals. The oil sight glass is sensitive to suspension changes from tires, suspension springs and shock air pressure, parked surface anomalies and even varied between bikes, etc. On some bike, sight glass was totally filled no matter the attitude.
Hence came the wise sage advice toward most for changing oil and don't bother with checking level. :bowdn:

On the other hand, my 1986 Suzuki LS650 Savage single cylinder air cooled was a different story. It ran hotter especially in warmer weather. Although it had tight compression, good valve guide seals and no oil leaks, it would consume a quarter quart of oil every 500 miles when temperatures got above 90 degrees F (32 C). There, I religiously checked the oil every other fill. :-? (Fuel fill was roughly every 100 miles, as I had a 2.8 gallon tank. Why manufacturers insist on cute looking small gas tanks on mid size cruisers beats me. Yet their 250 cc single cylinder GZ250 Marauder had a 4 gallon tank. :shock: Some have ruined the engine by failing to check and maintain oil level. :oops: )

After riding the 250 Honda Rebels and Suzuki Marauders at an MSF course (employer safety training requirement on government installations regardless of riding experience), the Savage felt and throttled like a "big bike" when riding home. :laughing:
George Hostler
Clovis, NM, US

Christian Motorcycle Association
Salvation Army Motorcycle Ministry, Western Territory
http://tsammcentral.org/
2001 Kawasaki ZG1200 Voyager XII
1971 Honda CB100
User avatar
dsmmrm
Cruiser
Cruiser
Posts: 92
Joined: Tue Jun 20, 2017 12:41 pm
7
Current bike(s): 2001 Kawasaki Voyager XII
1996 Kawasaki Vulcan 1500 Classic
Has liked: 0
Been liked: 3 times

Re: Oil sight glass

Post by dsmmrm »

My concern is more monitoring the engine health as it ages. I'm not real concerned about usage with 34k on it now but once I pass 100k and up it would be nice to have a feel for how the engine is evolving, specifically with regard to rings, valve guides, etc. Over the years I have found that monitoring small changes in various subsystems can alert you to big failures before they happen, specifically with regard to consumption of oil, fuel, and coolant that fall outside of normal expectations.

I Just got the filter, this weekend I'll do the oil change with he recommended type and amount of oil and note the sight glass reference point while on the center stand in the middle of my garage after letting it set for a while. That should give me enough info for my purposes. It's not a space shuttle, after all, an ounce or 2 either way won't make it blow up (I hope).
--
Dave Morrow
Vermilion, Ohio
small herd of kaws
User avatar
ghostler
Grand Tourer
Grand Tourer
Posts: 519
Joined: Fri Jun 21, 2013 5:44 pm
11
Current bike(s): 2001 Voyager XII, 1971 Honda CB100
Asphalt, the final frontier; these are the treks of the Kawasaki Voyager; its continuing mission to explore strange new roads, to seek out new sites, new bed & breakfasts, to boldly ride where no one has ridden before.
Location: Clovis, NM
Has liked: 2 times
Been liked: 10 times
Contact:

Re: Oil sight glass

Post by ghostler »

Dave, after reading comments in this and various forums on the XII, the bike's engine is rock solid if maintained. Similar to other tourers like the Hondas, it is not unusual to put a couple hundred thousand miles on the engine without major work. That's why there are still a lot of them on the road and in use. If something should happen and the engine is ruined, it's cheaper to buy a good used one from Carl Leo or other reputable salvage dealers for under $1k, and keep the legacy going.
:thmup:
George Hostler
Clovis, NM, US

Christian Motorcycle Association
Salvation Army Motorcycle Ministry, Western Territory
http://tsammcentral.org/
2001 Kawasaki ZG1200 Voyager XII
1971 Honda CB100
User avatar
cranky
King of the Road
King of the Road
Posts: 1037
Joined: Wed Jul 06, 2016 12:36 am
8
Current bike(s): 2003 Voyager
Location: San Jose, KalEfornYa
Has liked: 303 times
Been liked: 80 times

Re: Oil sight glass

Post by cranky »

dsmmrm wrote:Over the years I have found that monitoring small changes in various subsystems can alert you to big failures before they happen, specifically with regard to consumption of oil, fuel, and coolant that fall outside of normal expectations.

I Just got the filter, this weekend I'll do the oil change with he recommended type and amount of oil and note the sight glass reference point while on the center stand in the middle of my garage after letting it set for a while. That should give me enough info for my purposes. It's not a space shuttle, after all, an ounce or 2 either way won't make it blow up (I hope).
+ a gazillion!!! Find a reference point that YOU know to be 3qt 22oz and know where Ya start and monitor
usage!!!!!! Not knowing will drive Ya nuts!!!! ..... er.... GBG IMHO, I don't care what Ya use for a reference
point, side/center on your right foot! Just know how to monitor change!!!!
'03 Voyager - http://tinyurl.com/mqtgpwp VROC pics of Gina
Cranky - Bill Snodgrass AVA # 6544. VROC # 16804
Cranked >128K miles, Mtn bike-no motor!!!
San Jose, KalEfornYa
User avatar
Mr Jensee
King of the Road
King of the Road
Posts: 1987
Joined: Fri Dec 26, 2008 5:55 pm
15
Current bike(s): Phone 337-781-8158
Home Phone disconnected.
Previous bikes. Yamaha 180, Honda CM200T, Suzuki 1000LNKawasaki ZRX1100.
Location: Lafayette, La
Has liked: 0
Been liked: 9 times

Re: Oil sight glass

Post by Mr Jensee »

This is the funnel I use to change oil. It is great because it has it marked in cc so you can accurately put in the correct amount of oil. It has a lid to keep oil from spilling and a valve and screen so you can shut off the flow if necessary.

http://ace.imageg.net/graphics/product_ ... enh-z8.jpg
For Voyager XII Manuals click the link below.
https://1drv.ms/f/s!Ao3K0Ai2gvglgS3l7J4pBJrjfBhc
User avatar
dsmmrm
Cruiser
Cruiser
Posts: 92
Joined: Tue Jun 20, 2017 12:41 pm
7
Current bike(s): 2001 Kawasaki Voyager XII
1996 Kawasaki Vulcan 1500 Classic
Has liked: 0
Been liked: 3 times

Re: Oil sight glass

Post by dsmmrm »

Oooh, I want one of those. Any idea where they can be had?
--
Dave Morrow
Vermilion, Ohio
small herd of kaws
User avatar
cranky
King of the Road
King of the Road
Posts: 1037
Joined: Wed Jul 06, 2016 12:36 am
8
Current bike(s): 2003 Voyager
Location: San Jose, KalEfornYa
Has liked: 303 times
Been liked: 80 times

Re: Oil sight glass

Post by cranky »

... I typed in "measure oil funnel" in a google search and of course Amazon to the
rescue... not the same but looks very workable.... http://tinyurl.com/ybh5ulvc

most oil containers are metered, you can look at the side and know how much
Ya are using, funnels are cheap.. JM2C
'03 Voyager - http://tinyurl.com/mqtgpwp VROC pics of Gina
Cranky - Bill Snodgrass AVA # 6544. VROC # 16804
Cranked >128K miles, Mtn bike-no motor!!!
San Jose, KalEfornYa
Post Reply

Return to “Tech Tips - Voyager XII (1200 Four)”