Cracked trunk lid

This is for general posts and questions concerning only the Voyager XII (1200cc, Four-cylinder) Years 1986 thru 2003.

Moderators: the2knights, Highway Rider

Post Reply
Eydugstr
Traveler
Traveler
Posts: 101
Joined: Fri May 27, 2016 8:29 pm
8
Current bike(s): 1990 Kawasaki Voyager xii
2005 Kawasaki Concours
1972/77 CB750
Location: Kansas City
Has liked: 0
Been liked: 5 times

Cracked trunk lid

Post by Eydugstr »

Working on a 90 xii, and one of the problems is the trunk lid. It has a cracked piece on the front right corner that seems to keep cracking despite three ABS cement fixes and shims placed inbetween the hinges. Is there something I'm overlooking? Are there any rubber bushings that wear out after a period of time that need to be replaced? The weatherstrip looks in good shape.
triton28
King of the Road
King of the Road
Posts: 1007
Joined: Fri Aug 23, 2013 1:32 am
11
Current bike(s): 1987 ZG-1200 B1
1987 ZG-1200 B1
1990 ZG-1200 B4
Location: Nova Scotia Canada
Has liked: 106 times
Been liked: 274 times

Re: Cracked trunk lid

Post by triton28 »

I have a complicated procedure which seems to work when I repair body items. I grind down the inner surface and the outer surface surrounding the crack/missing piece using a Dremel with carbide burrs. The extent to which I relieve the lateral area of the plastic depends upon the size/shape of the repair I want to make, but I always go at least 1" beyond the edge of the crack/missing area.
What's left is a portion of plastic in the middle of the the original thickness of the plastic which then gets sandwiched on both the inner AND outer surface between multiple layers of epoxy, NOT polyester, resin soaked fiberglass cloth and sometimes strand if it is a curved inside surface. Sort of like a tenon of a mortise and tenon woodworking joint being brought back to the original thickness of the board before the tenon was machined.
The area I had ground down provides sufficient depth for the cloth without being above the adjacent finished surface surrounding the area being repaired. Low is better than high, as sanding is a pain in the butt unless it is spot and glazing putty to get fair with the original surface. Then it's time for primer, more spot and glazing putty, primer etc. etc. and then base and clear coat.
It's a lot of work but I find it works for me.
Dave
Eydugstr
Traveler
Traveler
Posts: 101
Joined: Fri May 27, 2016 8:29 pm
8
Current bike(s): 1990 Kawasaki Voyager xii
2005 Kawasaki Concours
1972/77 CB750
Location: Kansas City
Has liked: 0
Been liked: 5 times

Re: Cracked trunk lid

Post by Eydugstr »

TY for the response - Hope it doesn't come to the point where I have to patch it with fiberglass or bondo...BTDT on sidecovers for other bikes before. Just wondered if there was something specific to these bikes to look for on the trunks.
User avatar
Mr Jensee
King of the Road
King of the Road
Posts: 1987
Joined: Fri Dec 26, 2008 5:55 pm
15
Current bike(s): Phone 337-781-8158
Home Phone disconnected.
Previous bikes. Yamaha 180, Honda CM200T, Suzuki 1000LNKawasaki ZRX1100.
Location: Lafayette, La
Has liked: 0
Been liked: 9 times

Re: Cracked trunk lid

Post by Mr Jensee »

You might want to check Ebay for someone selling off trunk lids or entire trunks. Usually these used parts are cheap.

http://www.ebay.com/itm/Kawasaki-Voyage ... KQ&vxp=mtr
For Voyager XII Manuals click the link below.
https://1drv.ms/f/s!Ao3K0Ai2gvglgS3l7J4pBJrjfBhc
Post Reply

Return to “General - Voyager XII (1200 Four)”